Schaeffler Product catalogue - medias
Ihre Eingaben des Auswahlassistenten werden im Hintergrund gespeichert, Sie können den Assistenten jederzeit wieder aufrufen.
(0)

YRTCM150-XL


Axial/radial bearings

double direction, screw mounting, with integrated angular measuring system

  
Send to shopping basket
Radial loadAxial load in one directionAxial load in two directionsMoments about all axesNot sealedGrease lubrication
Hole pattern
2 retaining screws (1)
 
d 150  mm  Tolerance: 0/-0,013
D 240  mm  Tolerance: 0/-0,015
H 41  mm  Attention!
H and H1 are 1 mm higher than the standard bearing YRT.
  34  Number of fixing holes in inner ring
Attention!
For fixing holes in the adjacent construction.
Note the pitch of the bearing holes.
  33  Number of fixing holes in outer ring
Attention!
For fixing holes in the adjacent construction.
Note the pitch of the bearing holes.
    The measuring head cannot be mounted between the fixing holes or the heads of the fixing screws. Two holes for fixing screws therefore remain unused in the bearing outer ring.
  2  Number of retaining screws
  3  Number of extraction threads
a 6,2  mm  Fixing holes in inner ring
C 12  mm   
D1 max 214,5  mm  Diameter of inner ring for design of adjacent construction
DM 213,82  mm  Diameter of dimensional scale on shaft locating washer
d1 7  mm  Fixing holes in inner ring
d2 11  mm  Fixing holes in inner ring
d3 7  mm  Fixing holes in outer ring
G M8  Extraction thread
H1 27  mm  Attention!
H and H1 are 1 mm higher than the standard bearing YRT.
H2 14  mm   
HM 10  mm   
J 165  mm  Fixing holes in inner ring
J1 225  mm  Fixing holes in outer ring
t 36 x 10°  Pitch t
Including retaining screws and extraction threads

Quantity X t
m 6,4  kg  ≈ Mass
MA 14  Nm  Screw tightening torque

Tightening torque for screws to DIN EN ISO 4762, grade 10.9.
Ca 128000  N  Basic dynamic load rating, axial
C0a 650000  N  Basic static load rating, axial
Cr 74000  N  Basic dynamic load rating, radial
C0r 146000  N  Basic static load rating, radial
Cua 65000  N  Fatigue limit load, axial
Cur 22100  N  Fatigue limit load, radial
nG 800  1/min  Limiting speed for electronic limiting speed and bearing
caL 3800  N/µm  Axial rigidity of bearing position
Rigidity values taking account of the rolling element set, rigidity of the bearing rings and the screw connections.
crL 3200  N/µm  Radial rigidity of bearing position
Rigidity values taking account of the rolling element set, rigidity of the bearing rings and the screw connections.
ckL 18600  Nm/mrad  Tilting rigidity of the bearing position
Rigidity values taking account of the rolling element set, rigidity of the bearing rings and the screw connections.
caL 12000  N/µm  Axial rigidity of rolling element set
crL 4800  N/µm  Radial rigidity of rolling element set
ckL 61000  Nm/mrad  Tilting rigidity of rolling element set
MR 4  Nm  Bearing frictional torque

Measurement speed n const = 5 1/min,
bearing temperature +50°C,
after grease distribution cycle;
frictional torque may increase by 2,5 times up to the limiting speed.
Schaeffler applies cookies to secure an optimal use. With the further use of this website you accept the application of cookies.  Further information